hl specifications typical applications 15a (1c), 10 a (2c) space saving power relay hl relays mm inch 27.2 1.071 35.4 1.394 20.8 .819 rohs directive compatibility information http://www.nais-e.com/ features ?high switching capacity in a compact size 1 form c (15 a 125 v ac), 2 form c (10 a 250 v ac) ?rugged construction for tough applications ?long life mechanical: min. 10 8 operations (dc), min. 5 10 7 operations (ac) electrical: min. 5 10 5 operations (except for 10 a 250 v ac of 2 form c) about cd-free contacts we have introduced cadmium free type products to reduce environmental hazardous substances. (the suf? ? should be added to the part number) please replace parts containing cadmium with cadmium-free products and evaluate them with your actual application before use because the life of a relay depends on the contact material and load. contacts #1 this value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. remarks * speci?ations will vary with foreign standards certi?ation ratings. * 1 measurement at same location as ?nitial breakdown voltage section * 2 detection current: 10 ma * 3 excluding contact bounce time * 4 half-wave pulse of sine wave: 11ms; detection time: 10 s * 5 half-wave pulse of sine wave: 6ms * 6 detection time: 10 s * 7 refer to 6. conditions for operation, transport and storage mentioned in ambient envi r onment characteristics (at 25 c 77 f , 50% relative humidity) arrangement 1 form c 2 form c initial contact resistance, max. (by voltage drop 6 v dc 1 a) 50 m ? contact material agsno 2 type rating (resistive) nominal switching capacity 15 a 125 v ac, 10 a 250 v ac 10 a 250 v ac max. switching power ac : 2,500 va dc: 90 w ac : 2,500 va dc: 90 w max. switching voltage 250 v ac 30 v dc 250 v ac 30 v dc max. switching current 15 a 10 a min. switching capacity #1 100 ma, 5 v dc expected life mechanical (at 180 cpm) 5 10 7 (ac), 10 6 (dc) electrical (resistive) 15 a 125 v ac 5 10 5 10 a 250 v ac 5 10 5 3 10 5 3 a 30 v dc 5 10 5 5 10 5 max. operating speed 20 cpm initial insulation resistance* 1 min. 100 m ? (at 500 v dc) initial breakdown voltage* 2 between contact sets 1,500 vrms for 1 min. between open contacts 1,000 vrms for 1 min. between contacts and coil 2,000 vrms for 1 min. operate time (at nominal voltage) max. 25 ms (dc type) max. 25 ms (ac type) release time* 3 (without diode) (at nominal voltage) max. 25 ms (dc type) max. 25 ms (ac type) t emperature rise, max. (at nominal voltage) max. 80 c shock resistance functional* 4 min. 196 m/s 2 {20 g} destructive* 5 min. 980 m/s 2 {100 g} vibration resistance functional* 6 10 to 55 hz at double amplitude of 1 mm destructive 10 to 55 hz at double amplitude of 2 mm conditions for operation, transport and storage* 7 (not freezing and condensing at low temperature) ambient temperature ?0 c to +70 c ?8 f to +158 f humidity 5 to 85% r.h. unit weight approx. 35 g 1.25 oz pow er station control equipment, refrigerators, building control equipment, of?e machines, and medical equipment. all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
hl ordering information coil data (at 20 c 68 f ) contact arrangement 1: 1 form c 2: 2 form c terminal arrangement h: plug-in hp: pc board htm: top mounting l: light emitting diode wired, plug-in pl: light emitting diode wired, pc board coil voltage ac 6, 12, 24, 48, 120, 240 v dc 6, 12, 24, 48, 110 v contact material f: agsno 2 type 2h hlex. ac240v f note: standard packing carton: 20 pcs., case: 200 pcs. ul/csa approved type is standard. dc coils ac coils at 60 hz coil voltage, v dc pick-up voltage, v dc (max.) drop-out voltage, v dc (min.) max. allowable v oltage, v dc coil resistance, ? ( 10%) nominal coil current, ma operating power, w nominal minimum 6 4.8 0.6 6.6 40 150 0.90 0.58 12 9.6 1.2 13.2 160 75 24 19.2 2.4 26.4 650 37 48 38.4 4.8 52.8 2,600 18.5 110 88.0 11.0 121.0 10,000 10 1.0 0.64 coil voltage, v dc pick-up voltage, v ac (max.) drop-out voltage, v ac (min.) max. allowable v oltage, v ac nominal coil current, ma operating power, va nominal minimum 6 4.8 1.8 6.6 200 1.20 0.77 12 9.6 3.6 13.2 100 24 19.2 7.2 26.4 50 48 38.4 14.4 52.8 25 110/120 88 36 132 10.9/11.9 220/240 176 72 264 6.0/6.5 notes: 1. the range of coil current is 15% for ac (60 hz), 10% for dc, at 20 c. 2. the relay may be used in the range of 80% to 110% of the nominal coil v oltage. however, it is recommended that the relay be used at 85% to 110% nominal voltage to take temporary voltage variations into consideration. 3. each coil resistance of dc types is the measured value at a coil temperature of 20 c. please allow a compensation of 0.4% resistance for each coil temperature change of 1 c. 4. all ac 240 v types are rated for double coil voltages, both ac 220 v and ac 240 v. 5. for use with 220 or 240 v dc, connect a resistor, as suggested below, in series with the 110 v dc relay. voltage 1 form c, 2 form c 220 v dc 240 v dc 11 kw (5 w) 13 kw (5 w) all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
hl dimensions mm inch tolerance: 0.5 .020 plug-in pc board* 1 top mounting hl1 (1 form c) hl2 (2 form c) 1.2 .047 accepts faston #187 schematic 2 6 87 3 20.8 .819 27.2 1.071 6.35 .250 10 .394 3.95 .156 4.6 .181 6 .236 7.15 .281 35.4 1.394 14.2 .559 ac type dc type 8 7 ( ) ( ) 3 2 6 8 7 ( ? ) ( + ) 3 2 6 20.8 .819 27.2 1.071 35.4 1.394 3 3 2 2 6 6 8 7 schematic 1.2 .047 0.5 .020 1.5 .059 5 .197 3.5 .138 1.5 .059 78 4.6 .181 4.6 .181 6 .236 7.15 .281 10 .394 14.2 .559 ac type dc type 8 7 ( ) ( ) 3 2 6 8 7 ( ? ) ( + ) 3 2 6 20.6 .811 43 1.693 3 3 2 6 87 2 6 8 7 schematic accepts faston #187 mounting dimension 2-3.2 to 3.5 dia 2 .079 1.2 .047 2-.126 to .138 dia 6.35 .250 3.6 .142 35.4 1.354 37.6 1.480 37.6 1.480 20.8 .819 35.4 1.394 27.2 1.071 1.2 .047 6.35 .250 10 .394 14.2 .559 3.7 .146 4.7 .185 6 .236 7.3 .287 1 3 5 7 accepts faston #187 8 2 4 6 schematic ac type dc type 8 7 ( ) ( ) 3 2 6 8 7 ( ? ) ( + ) 3 2 6 27.2 1.071 1.2 .047 0.5 .020 1.5 .059 20.8 .819 35.4 1.394 3.5 .138 1.5 .059 1 78 1 3 5 78 2 4 6 3 5 2 4 6 schematic 5 .197 4.7 .185 6 .236 7.3 .287 10 .394 14.2 .559 ac type dc type 8 7 ( ) ( ) 3 2 6 8 7 ( ? ) ( + ) 3 2 6 20.6 .811 37.6 1.480 37.6 1.480 2 .079 43 1.693 1.2 .047 1 1 2 4 65 3 87 3 5 2 4 6 78 schematic accepts faston #187 mounting dimension 2-3.2 to 3.5 dia. 2-.126 to .138 dia. 6.35 .250 3.6 .142 34.4 1.354 * 1 pc board pattern copper-side view (hl1) (hl2) 5-2 dia. 5-.079 dia. 7.15 .281 17.75 .700 8.5 .335 14.2 .559 4.6 .181 6 .236 4 .158 4 .158 4 .158 10 .394 1.25 .049 1.25 .049 1.25 .049 r3 r2 8-2 dia. 8-.079 dia. 7.3 .287 18 .709 13.3 .524 14.2 .559 2 .079 10 .394 2 .079 r2 r2 tolerance: 0.1 .004 all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
hl accessories mm inch hl1-ss-k (with hold-down clip) 25.5 1.004 18.7 .736 11.2 .441 29.4 1.157 accepts faston #187 0.23 .009 4.75 .187 panel cutout 25.8 1.016 21.6 .850 hl2-ss-k (with hold-down clip) 25.5 1.004 18.7 .736 11.2 .441 29.4 1.157 accepts faston #187 0.23 .009 4.75 .187 panel cutout 25.8 1.016 21.6 .850 plug-in terminal socket mount simply insert socket into panel hole and push down as indicated to lock socket in place. panel cutout for tandem mounting tolerance: 0.1 .004 1.0 to 2.0 .039 to .079 panel thickness 25.8 1.016 8.9 .350 25.8 1.016 21.6 .850 21.6 .850 5.9 .232 minimum separation distance 2. pc board terminal socket hl1-ps-k 21.2 .835 16.2 .638 11.2 .441 0.23 .009 2.0 .079 1.0 .039 29.4 1.157 pc board pattern 15.3 .602 10 .394 5-2.4 dia. 5-.094 dia. 17.45 .687 12.75 .502 6.75 .266 hl2-ps-k 21.2 .835 16.2 .638 11.2 .441 0.23 .009 2.0 .079 1.0 .039 29.4 1.157 pc board pattern 15.3 .602 10 .394 8-2.4 dia. 8-.094 dia. 17.45 .687 12.75 .502 6.75 .266 layout for tandem mounting (2 form c) tolerance: 0.1 .004 10 .394 23.2 .913 10 .394 (6.6) (.260) (5.3) (.209) 17.45 .687 17.45 .687 17.25 .679 15.3 .602 7.9 .311 15.3 .602 2.4 dia. .094 dia. all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
hl for cautions f or us e , see rel a y t e c hnical in f ormation 3. screw terminal socket for din rail assembly hl2-sfd-k (with hold-down clip) 5 7 4 8 1 6 3 2 m3.5 terminal screw 26 0.6 1.024 .024 28.6 0.6 1.126 .024 30 0.6 1.181 .024 8 .315 21.1 0.6 .831 .024 10 0.2 .394 .008 15.3 0.2 .602 .008 4.65 0.2 .183 .008 1.35 0.1 .053 .004 9.35 0.2 .368 .008 8.1 0.2 .319 .008 10 0.3 .394 .012 67 1 2.638 .039 schematic 21 43 65 87 layout for tandem mounting tolerance: 0.1 .004 8 .315 26 1.024 26 1.024 30 1.181 30 1.181 4 .158 33.5 1.319 67 2.638 minimum separation in tandem mounting 2-m3.5 screw holes or 2-4.2 0.1 dia. (remark) max. continuous current of all hl sockets is 10 a. mm inch all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
|
